Using this design, you
can construct an electromagnetically impulsed pendulum clock with a
1-second beat. On the prototype, the pendulum rod is 115cm long with a
bob adjusted to make it beat every second. It is suspended on a short
piece of mainspring from a watch, which is attached to a vertical
backboard with a 6mm screw. The rod extends some 15cm below the bob and
is fitted with large washes at the lower end. Note that for a pendulum
to beat in seconds, there must be 99.4cm distance between the support
and the centre of mass of the pendulum. Between the bob and the lower
end is a 5mm wide white reflector facing back.
Below the rod and 15mm to the left is the impulse solenoid, with a
core but no actuator attached. The circuit comprises of four parts: (1)
the sensor; (2) the counter and solenoid driver; (3) the clock driver;
and (4) the clock. The sensor is built on its own small piece of strip
board and is located on the centre line of the backboard behind the
reflector. It utilises a Sharp IS471F infrared modulated detector
(Farnell cat. 414-2860) to eliminate interference from external light
sources. The infrared emitter (IRLED1) must be mounted near to the
detector (IRDET1) but be masked from it.
The emitter radiates a coded signal toward the reflector. As the
pendulum passes the centre line it reflects the signal back to the
detector, which then gives a negative-going output pulse on pin 2. This
makes the surface-mount LED (LED1) flash once.
It also sends a signal to the counter and clock driver circuits on the
main circuit board. Pulses from the sensor are fed into IC1, a 4020
14-stage ripple counter. The counter’s output (pin 6) goes high every
128 counts (seconds). These long duration pulses are inverted by
transistor Q1 and differentiated by the 10nF capacitor and 22kO
resistor, providing a narrow trigger pulse for a 7555 CMOS timer (IC2).
The 7555 is wired as a monostable, driving the base of transistor Q3
with a relatively short pulse width suitable for energising the impulse
solenoid. LED2 flashes in unison with solenoid pulses, and can be
mounted right on the solenoid as a visual aid. Pushbutton switch S2 is
used to provide gentle starting pulses to get the pendulum swinging
smoothly at the outset. Switch S1 resets the counter to zero. With this
arrangement, the pendulum is set swinging and when it is to the left of
centre, S1is pushed. Thus, the pendulum moves right to left on even
numbered counts. At the 128th count, the solenoid gives a shot pull to
the left just as the pendulum is passing through the centre line and
moving right to left.
The distance of the solenoid below the pendulum is adjusted so that
it does not jerk the pendulum but adds a gentle nudge. The clock driver
circuit also derives its timing from the output of the sensor.
Negative-going pulses from the sensor are inverted by Q4 before being
fed into a 4013 flipflop. On the output side, pins 12 & 13 go high
in turn for one second. These pulses are too long to directly drive the
clock coil, so they’re logically “anded” with the short pulses from the
sensor using two gates of a 4093 NAND Schmitt trigger (IC4). The outputs from these gates then drive an adapted quartz clock movement.
A suitable clock can be made from a standard quartz movement by isolating the coil and removing the battery. See SILICON CHIP,
Dec. 1996, page 38 for full instructions or October 2001 page 37 for
brief notes. This is an experimental clock so you may have to try
various solenoids to find one that works for you. If necessary, the
solenoid pulse duration can be changed by varying IC2’s timing
components. If the suspension is too stiff, try impulsing at 64 beats
from pin 4 of IC1, but note that the aim is to get the freest pendulum
movement possible. The Synchronome and Hipp clocks were impulsed at
30-second intervals, so your clock could be even better.
In the prototype, the reflector was made from the back of an
adhesive cable clip snapped on to the pendulum rod. The white back was
masked to give a 5mm wide central vertical strip, giving clean, short
pulses as the pendulum passes. Current drain is several milliamps, so
the prototype was powered from an SLA battery
fed from a float charger. A pendulum beating in seconds is called a
Royal pendulum. Its length is the same as one in a typical long case
Author: A. J. Lowe – Copyright: Silicon Chip Electronics