DC Voltmeters


DC Voltmeter Block Diagram

DC voltmeter mainly consists of a dc amplifier apart from the attenuator, as shown in figure.

DC Voltmeter Block
DC Voltmeter Block Diagram

DC voltmeters can further be divided into two categories.

1. Direct Coupled Amplifier DC Voltmeter.

DC Voltmeter using direct coupled amplifier
DC Voltmeter

This type of voltmeter is very common because of its low cost. This instrument can be used only to measure voltages of the order of milli-volts owing to limited amplifier gain.The circuit diagram for a direct coupled amplifier dc voltmeter using cascaded transistors is shown in figure.An attenuator is used in input stage to select voltage range. A transistor is a current controlled device so resistance is inserted in series with the transistor Q1 to select the voltage range. It can be seen from figure that sensitivity of voltmeter is 200 kilo ohms/volt neglecting small resistance offered by transistor Q1. Other values of range selecting resistors are also so chosen that sensitivity remains the same for all ranges. So current drawn from the circuit is only 5micro Ampere.

Two transistors in cascaded connections are used instead of using a single transistor for amplification in order to keep the sensitivity of the circuit high. Transistors Q1 and Q2 are taken complement to each other and are directly coupled to minimize the number of components in the circuit. They form a direct coupled amplifier.A variable resistance R is put in the circuit for zero adjustment of the PMMC. It controls the bucking current from the supply E to buck out the quiescent current.The draw-back of such a voltmeter is that it has to work under specified ambient temperature to get the required accuracy otherwise excessive drift problem occurs during operation.

Direct Coupled Amplifier Transistorized DC Voltmeter using FET
DC Voltmeter using FET

Another circuit diagram of a direct coupled amplifier dc voltmeter using FET in input stage is shown in figure.In this voltmeter, voltage to be measured is firstly attenuated with range selector switch to keep the input voltage of amplifier within its level. FET is used in the input stage of amplifier because of its high input impedance so that is does not load the circuit of which voltage is to be measured and it also keeps the sensitivity of voltmeter very high.As FET is a voltage controlled device so resistance network of attenuator is put in shunt in the circuit.Transistors Q2 and Q3 form the direct coupled dc amplifier whose output is finally supplied to PMMC meter. When transistors work within their dynamic region, the deflection of meter remains proportional to the applied input voltage. This voltmeter can be used for measurement of voltages of the order of milli-volts because of sufficient gain of amplifier.

Apart from the high input impedance, this circuit has another advantage that when input voltage exceeds its limit, amplifier gets saturated which limits the current passing through the PMMC meter. So meter does not burn out.

2. Chopper Type DC Voltmeter.

Chopper Type DC Voltmeter Block
Chopper Type DC Voltmeter

Chopper type dc amplifier is used in highly sensitive dc electronic voltmeters. Its block diagram is shown in figure. Firstly dc input voltage is converted into ac voltage by chopper modulator and then it is supplied to an ac amplifier, i Output of amplifier is then demodulated toa dc voltage proportional to the original input voltage. Modulator chopper and demodulator chopper act in anti-synchronism.Chopper system may be either mechanical or electronic.

Chopper Type DC Voltmeter   Circuit
Chopper Type DC Voltmete

Circuit diagram of an electronic chopper employing photo diodes is shown in figure.Photo diodes change its resistance under different illumination conditions, this property f photo diode is used in chopper amplifier. Its resistance changes from the order of few mega-ohms to few hundred ohms when it is illuminated by a light source in the dark place.

Two neon lamps are used in this circuit, these are supplied by an oscillator for alternate half cycles. Two photo diodes are used in input stage which acts as half-wave modulators because of its alternate switching action by the neon lamps at the frequency of oscillator.

Output of chopper modulator is a square wave voltage (proportional to the input signal) which is supplied to the ac amplifier through a capacitor. Amplified output is again passed through a capacitor and then fed to chopper demodulator. Capacitor is used to remove dc drift from the signal. Chopper demodulator gives a dc output voltage (proportional to the input voltage) which is passed through the low pass filter to remove any residual ac component. Now this dc output voltage is supplied to the PMMC meter for measurement of input voltage.

In chopper amplifier dc voltmeter, input impedance is of the order of hundred mega-ohms and it has sensitivity of one micro-volt per scale division.


Sorry, comments are closed!