Curious C-Beeper


Curious C Beeper

Curious C-Beeper is a fun to build little probe that can be used to quickly detect the capacity of capacitors in pF nF range, test their stability with temperature changes, find broken wires, locate wires, trace wires on PCBs, and to locate live wires behind the walls without touching them. The circuit uses three transistors to make a most unusual capacitance beeper probe. When a capacitor is touched to the probe, the probe beeps at a frequency that varies with capacitance. The frequency change is so steep with capacitance that tiny capacitors may be precisely matched or an exact fixed value may be selected to replace a trimmer in a prototype. If the user has reasonably moist skin, simply holding one lead of the capacitor to be tested while touching the other lead to the probe is all that is necessary. The user’s body forms the other connection through the beeper’s metal case. When the beeper is properly adjusted it draws only 10 uA with nothing touching the probe – no power switch is required. This design is optimized for capacitors less than about 0.1 uF (100 nF). Large capacitors give a low frequency “clicking” sound and small capacitors sound a tone that increases as the capacitance decreases. Many decades of frequency change occur over the beeper’s range giving even the more tone-deaf among us sufficient change to discern slight differences in capacitance. The entire device is powered by two CR2032 lithium cells that fit into TicTac box. The use of power switch is unnecessary since the circuit consumes almost no power when not being used.

Curious C Beeper

The Curious C-Beeper will become indispensable in virtually no time and has many uses such as:



Quickly match capacitors and trimmers. Forget the capacitance meter when matching parts from the parts bin or selecting a fixed value to replace a trimmer – the “fingers as conductors” feature makes the C-Beeper super-fast when searching for that perfect value.



Easily detect tiny variations when a capacitor is heated or cooled to quickly discriminate between NPOs and “Stable” dielectrics. General purpose and temperature compensating dielectric are quite easy to spot.



The C-Beeper makes an excellent cable fault locator – the end with the open will have less capacitance and beep at a much higher pitch or not at all. A break along an unshielded bundle can be spotted by grabbing the bundle at various points while listening for the capacitance change.



Identify which wire is which at the end of a bundle without stripping back the insulation. Touch the bare wire at one end with the C-beeper probe and pinch the still-insulated wires at the opposite end. The right wire will drop the pitch.



Identify traces on unpopulated PCBs right through solder mask – touch the C-beeper to the exposed end of the trace and use a finger to follow the trace across the board.



Check the value of feed through capacitors after they are installed – a difficult operation with a capacitance meter.



Identify varicap diodes. They beep at a much lower pitch than regular diodes.



Make a small flat plate electrode and line voltage electric fields may be detected. Follow wires behind walls and ceilings or determine if wires are “hot” without touching them. The C-Beeper’s tone is modulated by the AC voltage causing a warbling sound. Circuits with lamp dimmers, solid-state switches or fluorescent bulbs are especially easy to detect due to the harmonics on the line.





List of components:

C1 trimmer capacitor 30pF

C2 1nF

D1 1N4148

LED1 LED3MM

Q1 BC559C

Q2 BC559C

Q3 BC549C

R1 1M

R2 2M

R3 5M

R4 2M

R5 1M5

R6 33k

R7 33k

R8 270R

SG1 Piezoelectric Speaker



The probe tip is made ​​from silver wire 0.8 mm. The box brings out the ground through a screw. C1 trims the capacitance set point for LED and Piezoelectric Speaker.

Curious C Beeper

Curious C Beeper

Curious C Beeper


Sorry, comments are closed!